Scythe Ashura CPU Cooler

This is the new Ashura CPU Cooler from Scythe. Supporting both Intel (LGA775/1155/1156/1366/2011) and AMD (AM2/AM2+/AM3/AM3+/FM1/FM2) processors, the cooler is equipped with six 6mm copper heatpipes, an aluminum heatsink and a 140mm ‘Hayabusa’ PWM fan that operates at 300 to 1300 RPM. The Ashura will go on sale from February 6th for 4,980 Yen (about $55).

•  JAN model number
  SCASR-1000 JAN: 4571225051987 
  
  
• 145 × 65 × 161mm height (heatsink only) 
  (With fan) 25mm thickness 140 × 140 × 
• Fan speed
  500 ± 300rpm ~ 1300rpm ± 10% 
• Noise13.0 ~ 30.7dBA
• Airflow
  37.37 ~ 97.18CFM 
• Static pressure
  1.47 ~ 10.0Pa / 0.15 ~ 1.02mmH2O 
• Corresponding socket
  intel socket 775/1155/1156/1366/2011 
  AMD Socket AM2/AM2 + / AM3/AM3 + / FM1/FM2 
• Heat pipe
  This 6 × 6mm diameter 
• Weight
  750g 
  
  
• Accessories
  Multi-language manual containing illustrated grease fan clip set 2 (including Japanese)
• Package dimension
  172 × 120 × 220mm 
• Package weight
  1330g

• CPU cooler side-flow design original size 

• Adopt a design type interference elimination 
  Structure 1) narrow fin & Variant type pipe 
  I reduce interference with the memory heat spreader with large 
  The surface area of the heat radiation fin design and fin narrow 
  I have placed a well-balanced six 6mm diameter heat pipes to maximize. 
  Height 161mm 2) 
  161mm to the overall height with a large cooler with 14cm fan 
  middle tower to the general case of 200mm width by suppressing 
  I was designed to fit. 
  ※ (such as a gimmick, and with the design of the side panel) the structure of the PC case 
  Please note that there is a case that can not be installed by the. 
  
  
• Adopted the PWM model "140 Hayabusa" new design 
  Round-shaped frame with the same screw hole position 120mm fan
  Adopted the PWM model "140 Falcon" 140mm fan new design. 
  While the amount of wind-driven specification and by "large blade and small shaft" 
  And reduction of air resistance by placing a slit in the blade 
  I tried to compatibility of design. 
  
  
• Specification also supports dual-fan 
  One fan can be installed up to two (factory, fan case fan 
  Retaining clip is supplied with 2 sets) 
  135 ~ 140mm fan compatible with the same screw hole position 120mm fan 
  Will be for thickness 25mm 120mm fan, or any fan. 
  
  
• Strengthen the fixing of the wire retaining clip fan 
  A general-purpose optimization and included 120mm fan to the fan 140 "Falcon" 
  Adopt a new wire clip to balance the suitability of when using. 
  
  
• Retention formula adopted for the first time the new bridge design 
  Method of passing the bridge at the base of the heat sink Metaruba
  Retention system adopted for the first time. 
  And simple rational and reliable fixation of large heat sink by this 
  I realized the installation procedure. 
  
  
• Wide range of design RPM 
  Optimum cooling performance for any rotational speed up to high rpm low rotation 
  Heat sink design is adopted. 
  Support from the silent mode to overclock ultimate pole. 
  The maximum number of revolutions own way the meaning and performance (the fan that is always exhibited 
  Become. The higher cooling performance is reset by raising the rotational speed of the fan 
  Rose to near, and peaked rapid cooling capacity does not occur. 
  In addition, a certain level of cooling performance even dropped the fan speed in reverse 
  Always maintained, design and rapid decline in cooling capacity does not occur 
  Will) 
  
  
• Compatible Intel / AMD Universal 
  
  
• Environmentally-friendly products RoHS compliant