Enermax Aquafusion 360 review LCS
Intel Core i5 11400F processor review
Corsair Vengeance RGB Pro SL 3600 MHz 32GB review
ASRock Z590 Extreme review
Gigabyte Radeon RX 6700 XT Gaming OC review
Corsair K70 RGB TKL keyboard review
Corsair RM650x (2021) power supply review
be quiet! Silent Loop 2 280mm review
Corsair K55 RGB PRO XT keyboard review
Guru3D Rig of the Month - March 2021
Guru3D Rig of the Month - February 2019
The February Rig Of The Month for 2019 is not necessarily the most beautiful one. However, it is very unique as it is a PC that resides inside a closet/wall.
Check the February edition of the Guru3D Rig of the month 2019, right here.
Guru3D Rig of the Month - January 2019 - 01/31/2019 03:40 PM
The first Rig Of The Month for 2019 is not necessarily the most beautiful one. However it is very unique and the amount of time that went into this PC, is staggering. But please do understand the craf...
Guru3D Rig of the Month - December 2018 - 12/27/2018 02:42 PM
The last one of this year is here, meet the Guru3D Rig of the month for December 2018. This month we're visiting the UK, no worries this is not about the Brexit, contrary, this is about a fantastic b...
Guru3D Rig of the Month - November 2018 - 11/29/2018 11:25 AM
This month we're visiting Cape Town, South Africa where ov3rvolt perhaps slightly pays some respect to Prince's Purple Rain. Then again, that was not the idea when he started building his rig two y...
Guru3D Rig of the Month - October 2018 - 10/31/2018 03:11 PM
When you think about Germany, Munich, and alcohol you think Oktoberfest and a good beer right? Well, that doesn't apply for Manuel Friedrich, he is from Munich, he probably likes a good beer, but lik...
Download: Guru3D RTSS Rivatuner Statistics Server 7.2.0 - 10/30/2018 10:55 AM
We just released a final build of RTSS (Rivatuner Statistics Server) build 7.2.0. RTSS is an integral part of tweaking tools like MSI AfterBurner and responsible for the overlay, video recording and s...
JamesSneed
Senior Member
Posts: 1142
Joined: 2017-02-14
Senior Member
Posts: 1142
Joined: 2017-02-14
#5645062 Posted on: 03/01/2019 01:11 AM
This was one of the more interesting setups I have seen. How were the peripheral/usb cable runs to the desk done, in the ceiling?
This was one of the more interesting setups I have seen. How were the peripheral/usb cable runs to the desk done, in the ceiling?
Treets
Junior Member
Posts: 1
Joined: 2019-03-01
Junior Member
Posts: 1
Joined: 2019-03-01
#5645148 Posted on: 03/01/2019 09:38 AM
Thanks all for your comments. Some answers:
Lay-out
- Indeed the idea was to integrate the PC's in the room and at the same time detach them from the desk to have a clean all-in-one PC look.
- the lay-out comes from both the idea to run the cables under the floor and the cooling design. For the cables that meant turning the MB upside down for the shortest possible cable run. That led to the 'Aorus' text being upside down as well
. For cooling I wanted the warm air to naturally rise, so intake at the bottom and exhaust at the top. That led to the radiator down low and the power supply at the top. The desk had to have a central 'leg' to route the cables through. I use active Club3D USB cables with the monitors as USB hub (so I needed enough ports there) and DVIGear (very thick) displayport cables. Runs fortunately very well.
Hardware choices
- I chose the Aorus MB because of the integrated 10GB NIC and the forced VRM cooling. The airflow is rather limited in this setup (I did not want to have fans visible); so with this MB that was taken care of automatically.
- it's a RTX2080: fast enough (I hope) and expensive enough (I'm sure)
WAF and money
- I actually designed the system deep enough in the closet such that the door can be fitted again. With only some ventilation holes in the door it would be much more stealthy. But actually my girlfriend liked it the way it is so I left it out
- Yes Samuel, lot of effort and saving up, then putting water in your expensive gear for the first time (first time water cooling for me). But if it works it's great!
Thanks all for your comments. Some answers:
Lay-out
- Indeed the idea was to integrate the PC's in the room and at the same time detach them from the desk to have a clean all-in-one PC look.
- the lay-out comes from both the idea to run the cables under the floor and the cooling design. For the cables that meant turning the MB upside down for the shortest possible cable run. That led to the 'Aorus' text being upside down as well
. For cooling I wanted the warm air to naturally rise, so intake at the bottom and exhaust at the top. That led to the radiator down low and the power supply at the top. The desk had to have a central 'leg' to route the cables through. I use active Club3D USB cables with the monitors as USB hub (so I needed enough ports there) and DVIGear (very thick) displayport cables. Runs fortunately very well.Hardware choices
- I chose the Aorus MB because of the integrated 10GB NIC and the forced VRM cooling. The airflow is rather limited in this setup (I did not want to have fans visible); so with this MB that was taken care of automatically.
- it's a RTX2080: fast enough (I hope) and expensive enough (I'm sure)
WAF and money
- I actually designed the system deep enough in the closet such that the door can be fitted again. With only some ventilation holes in the door it would be much more stealthy. But actually my girlfriend liked it the way it is so I left it out
- Yes Samuel, lot of effort and saving up, then putting water in your expensive gear for the first time (first time water cooling for me). But if it works it's great!
Click here to post a comment for this news story on the message forum.
Senior Member
Posts: 206
Joined: 2016-12-28
Very different in a good way.
And the girlfriend has to be incredible too. The WAF was steep here