Cryorig releases Full Copper C7 Cu Heatsink
After nearly a year from first announcing the Cu line of full copper coolers PC cooling innovator CRYORIG is now releasing the C7 Cu copper enhanced SFF ITX cooler. The C7 Cu is built from the C7 architecture with one obvious upgrade, the extravagant use of copper for the whole heatsink body.
By exchanging for a full copper build from aluminum has allowed the C7 Cu see improvements of up to 15% in thermal performance. The increased thermal performance without increased size is a key advantage of the C7 Cu especially in ultra-compact SFF/ITX builds where space is limited.
Aimed at solving the space limits of Small Form Factor ITX systems, the C7 Cu was set with the task of further improving performance but without increasing size or fan speed. Utilizing higher thermal conductive materials was the only answer for the C7 Cu. Copper is nearly twice as thermal conductive as aluminum but nearly three times as expensive. That’s why copper is normally only used on the most thermal critical components such as heatpipes and heatsink base plates. With the C7 Cu, CRYORIG has swapped out the aluminum elements of the C7 with pure copper. Thermal performance gains are close to 15% when compared to the original C7.
Built on the original C7 architecture, users can except to get the same features such as Zero Interference design on both Intel and AMD boards, included installation tool, and pre-installed 92 mm PWM fan with integrated anti-vibration pads aimed for SFF/ITX systems. The 92mm fan features CRYORIG’s Quad Air Intake system, with additional intakes are placed at the four corners of the fan. This allows the fan to pull air from the sides not just from the top, because in most SFF/ITX systems there’s limited space for air intake between the top of the heatsink and the case side panel.
The C7 Cu is set to release in mid to late April in Asia and late May to early June in the USA and Europe. Pricing is set at MSRP 49,95 USD (-tax) in the USA and 49,95 (vat incl.) in Europe.
C7 Cu Specification |
|
Dimensions with Fan |
L97 x W97 x H47 mm |
Weight (with Fan) |
675 g |
Weight (without Fan) |
613 g |
Heatpipes |
4 units 6 mm Copper Heatpipes |
Fin |
T = 0,4 mm; Gap = 1,2 mm |
Fin Pcs |
57 pcs |
Base & Fins |
Pure Copper |
RAM Height Limit |
Limitless |
TDP: |
115 W |
Fan Specification |
|
Dimensions (L x W x H) |
92 x 92 x 15 mm |
Weight |
62 g |
Rated Speed |
600 ~ 2500 RPM ±10 % |
Noise Level |
30 dBA |
Air Flow |
40,5 CFM |
Air Pressure |
2,8 mmH2O |
Ampere |
0,2 A |
Cryorig Offers Taku Monitor Stand ITX Case at 299 USD - 11/08/2017 10:43 AM
CRYORIG is releasing the Taku PC monitor stand ITX case. The Taku has been in development for over 2 Years in house, with over 1 year of co-development with manufacturing partner Lian Li. ...
CRYORIG Releases the Taku Monitor Stand PC Case on Kickstarter - 05/29/2017 06:27 AM
The TAKU has been in development for over 2 Years in house, with over 6 months of co-development with manufacturing partner Lian Li. ...
CRYORIG Announces New R5 Cooler and Cu Line Performance Coolers - 05/24/2017 11:07 AM
Cryorig is announcing two new CPU cooling projects ahead of Computex 2017. The CRYORIG R5 high-end single tower and the Cu Series of Copper Fin enhanced coolers. The R5 is the second cooler in CRYORI...
CRYORIG Releases NZXT CAM Powered H7 Quad Lumi RGB Cooler - 05/17/2017 10:36 AM
CRYORIG announces their collaboration project with NZXT, the software controlled RGB LED H7 Quad Lumi will be releasing this June....
CRYORIG Also Provides Free AM4 update kit - 01/25/2017 06:23 PM
In response to AMD’s soon to be released Ryzen CPU and AM4 platform, PC thermal solution brand CRYORIG will be providing free AM4 upgrade kits soon after the official release of the AMD Ryze...
Senior Member
Posts: 1994
Joined: 2007-01-16
50euro for this piece of crap? Just as badly priced as that poc of a cooler MASTERAIR G100M.
https://www.reddit.com/r/sffpc/comments/8bipn5/quick-hands-on-the-cryorig-hu-c7/
Testing a hot chip with an overclock on a cooler meant for an ITX build? It didn't do to bad really considering it's size...
Senior Member
Posts: 2843
Joined: 2009-09-15
The testing was done at 4.3GHz@1.13v. With a delidded 8700K+Conductonaut and graphene coating which supposedly improves temps even if slightly.
Unless I had a brain fart and read/understood that entirely thread over there wrongly. :p
Funny note: I have a stock Intel cooler on my 8700K atm running at 4.2GHz@1.16v with 4GHz cache and 4000C18 ram. I will try and replicate his tests. brb
Edit: 1-2mins in RB 2.44/2.56, my cpu saw 100c for the first(and last) time. lol
Senior Member
Posts: 598
Joined: 2017-02-04
TEST Results---->https://www.techpowerup.com/reviews/CRYORIG/C7/6.html So add 15% to the results and it's still bad. Save your money and buy an aio liquid cooler. Stay away from this ineffective and curious fan impersonating a cooler. 40CFM?
Might as well cool your cpu fanning it with a folded up piece of paper.
Senior Member
Posts: 1994
Joined: 2007-01-16
Save your money and buy an aio liquid cooler. Stay away from this ineffective and curious fan impersonating a cooler. 40CFM?
Might as well cool your cpu fanning it with a folded up piece of paper.
Again it's not a cooler for overclocking with, it's only got a TDP rating of 115W barely enough for a stock 8700k, a little overclock will definitely exceed that.
It's just a cooler for small builds and additionally, just paying for the name more than anything else.
Senior Member
Posts: 2843
Joined: 2009-09-15
50euro for this piece of crap? Just as badly priced as that poc of a cooler MASTERAIR G100M.
https://www.reddit.com/r/sffpc/comments/8bipn5/quick-hands-on-the-cryorig-hu-c7/