ECS GeForce 9800 GTX+ Hydra SLI - 15 - Overclocking & Tweaking

by Hilbert Hagedoorn on: 09/08/2008 02:00 PM [ ] 0 comment(s)

Overclocking & Tweaking

As most of you with most videocards know, you can apply a simple series of tricks to boost the overall performance a little. You can do this at two levels, namely tweaking by enabling registry or BIOS hacks, or very simple, tamper with Image Quality. And then there is overclocking, which will give you the best possible results by far.

What do we need?
One of the best tool for overclocking NVIDIA and ATI videocards is our own Rivatuner that you can download here. If you own an ATI or NVIDIA graphics card then the manufacturer actually has very nice built in options for you that can be found in the display driver properties.

Where should we go ?
Overclocking: By increasing the frequency of the videocard's memory and GPU, we can make the videocard increase its calculation clock cycles per second. It sounds hard, but it really can be done in less than a few minutes. I always tend to recommend to novice users and beginners not to increase the frequency any higher then 5% of the core and memory clock. Example: If your card runs at 600 MHz (which is pretty common these days) then I suggest you don't increase the frequency any higher than 30 to 50 MHz.

More advanced users push the frequency often way higher. Usually when your 3D graphics start to show artifacts such as white dots ("snow"), you should back down 10-15 MHz and leave it at that. Usually when you are overclocking too hard, it'll start to show artifacts, empty polygons or it will even freeze. Carefully find that limit and then back down at least 20 MHz from the moment you notice an artifact. Look carefully and observe well. I really wouldn't know why you need to overclock today tested cards anyway, but we'll still show it ;)

All in all... do it at your own risk.

Check this out:

As you can see, the result is again a notably faster performing card. The game you are looking at is Crysis with the image quality settings as shown before (medium). We got the core to 828 MHz, the Shaders to 2052 MHZ and the memory over 2538 MHz (effective). Which really is just a nice overclock. We had some room for more though, yet settled as the overclock itself did not have a huge impact on performance.

Don't over-do your tweaks though, and be careful.

Overclocking results typically result into slightly more heat build-up in the GPU as well, but not with this water-cooler. Heavily stressed the core temperature remained at a level ~44-46 degrees C. And that is just grand.

ECS GeForce 9800 GTX+ Hydra

16 pages « < 13 14 15 16

ECS GeForce GTX 560
The GeForce GTX 560 we'll review in this article comes from ECS, out of the three products GTX 560 tested today here on Guru3D.com this one is reference clocked, has a reference design and a reference cooler. So this product will be the baseline performance product. Now that does not mean a sober product contrary, baseline performance is pretty good for the money. And next to that, we all know you'll gain the most from the less expensive products one you go and tweak them.

ECS GeForce GTX 460 Black review
We review the ECS GeForce GTX 460 Black series. Within the entire scope of Fermi GPU based graphics cards from NVIDIA the GeForce GTX 460 has to be the most interesting in terms of value for money with very acceptable decent thermals and power consumption. This is why we see a lot of SKU's released for this product, with a variety of cooling and factory overclocks. ECS Elite group also release a handful of GeForce GTX 460 cards, based on the reference design, slight overclock yet also a BLACK series graphics card which is a factory overclocked model with an Arctic cooling Accelero Xtreme PRO cooler sitting on top of that GPU.

ECS GeForce GTS 250 1024MB review | test
ECS GeForce GTS 250 tested -- Today the turn goes to the folks at ECS. Ever since the past year or two they have been trying hard to get a grip in the e-tail and retail channel, and as a brand they certainly are growing. With a creative product design and marketing team they present us some fairly special designs and concepts. Today's product tested is not at all different. Though we'll stubble into a reference clocked product, there is very little little reference otherwise.

ECS GeForce 9800 GTX+ Hydra SLI
A review on the ECS GeForce 9800 GTX+ Hydra SLI. Basically you'll receive two pre-modified GeForce 9800 GTX+ products and a water-cooling kit that is supplied by Thermaltake. It's in fact the Thermaltake big water series that you can slide into you 5.25"drive bay easily. Pretty much the only thing you need to do is connect four tubing connections, fill her up, connect some wiring ... and you are good to go. That's 15 minutes tops to get a gaming performance level better than the GeForce GTX 280.