BFG GeForce 9800 GTX 512MB OCX review

Graphics cards 1048 Page 4 of 15 Published by

teaser

4 - GPU temps, power cosumption & noise levels

Power consumption

Alright then, we just installed the card into out test-system and will monitor a couple of pretty important items.

We'll now show you some tests we have done on overall power consumption of the PC. Looking at it from a performance versus wattage perspective, the power consumption is not as bad as I expected it to be, yet it is a lot. The card according to our findings will consume close to ~150 Watts.

Our test system contains a Core 2 Duo X6800 Extreme Processor, the nForce 680i mainboard, a passive water-cooling solution on the CPU, DVD-rom and WD Raptor drive.

Power Consumption of the PC measured at wall socket:

  • GPU in IDLE -166W
  • GPU at 100% load - 310W

The methodology is simple: have a wattage monitor keeping a close eye on power consumption during our entire test-session. This device will register the maximum wattage pulled from the wall power outlet.  You are not looking at the power consumption of the graphics card, but the consumption of the entire PC. We had a total system wattage peak at roughly 310 Watts with the 9800 GTX card installed, which is a lot, but not at all shocking in this era.

The new G92 65nm cores are more power efficient than the G80 generation. So while power consumption is high, it's not at all higher then the last gen 8800 GTX product.

So here's my power supply recommendation:

  • A single GeForce 9800 GTX requires you to have a 450 Watt power supply unit at minimum if you use it in a high-end system. That power supply needs to have (in total) at least 25-30 Amps available on the 12 volts rails.
  • A second GeForce 9800 GTX installed is another ballgame though; on this system it requires you to have a 750 Watt power supply unit at minimum if you use it in a high-end system. That power supply needs to have (in total) at least 45 Amps available on the 12 volts rails.
  • A third GeForce 9800 GTX requires you to have a 1000 Watt PSU, with recommended 55 AMPs available on the 12 volts rails.

There are many good PSU's out there, please do have a look at our PSU reviews as we have loads of recommended PSU's for you to check out in there. What would happen if your PSU can't cope with the load?:

  • bad 3D performance
  • crashing games
  • overclocking issues
  • spontaneous reset or imminent shutdown of the  PC
  • freezes during gameplay
  • PSU overload can cause it to break down
Noise Levels coming from the graphics card

When graphics cards produce a lot of heat, usually that heat needs to be transported away from the hot core as fast as possible. Often you'll see massive active fan solutions that can indeed get rid of the heat, yet all the fans these days make the PC a noisy son of a gun. I'm doing a little try out today with noise monitoring, so basically the test we do is extremely subjective. We bought a certified dBA meter and will start measuring how many dBA originate from the PC. Why is this subjective you ask? Well, there is always noise in the background, from the streets, from the HD, PSU fan etc etc, so this is by a mile or two not a precise measurement. You could only achieve objective measurement in a sound test chamber.

The human hearing system has different sensitivities at different frequencies. This means that the perception of noise is not at all equal at every frequency. Noise with significant measured levels (in dB) at high or low frequencies will not be as annoying as it would be when its energy is concentrated in the middle frequencies. In other words, the measured noise levels in dB will not reflect the actual human perception of the loudness of the noise. That's why we measure the dBa level. A specific circuit is added to the sound level meter to correct its reading in regard to this concept. This reading is the noise level in dBA. The letter A is added to indicate the correction that was made in the measurement. Frequencies below 1kHz and above 6kHz are attenuated, where as frequencies between 1kHz and 6kHz are amplified by the A weighting.

table_tl.gif

 

table_tr.gif
blank.gif
TYPICAL SOUND LEVELS
Jet takeoff (200 feet) 120 dBA  
Construction Site 110 dBA Intolerable
Shout (5 feet) 100 dBA  
Heavy truck (50 feet) 90 dBA Very noisy
Urban street 80 dBA  
Automobile interior 70 dBA Noisy
Normal conversation (3 feet) 60 dBA  
Office, classroom 50 dBA Moderate
Living room 40 dBA  
Bedroom at night 30 dBA Quiet
Broadcast studio 20 dBA  
Rustling leaves 10 dBA Barely audible
blank.gif
table_bl.gif blank.gif table_br.gif

Not too bad, the reference cooler though you can hear yet remains silent. We measure roughly 40 DBa from the (entire) test system. The low noise design definitely works fine. This is at idle though.

When we start to stress and heat up the GPU cores the RPM of the fans will increase. Still not bad but our results end at 44 DBa which is noticeable, but not at all annoying.

 

BFG GeForce 9800 GTX OCX core temperatures

Let's have a look at the temperatures these single slot design coolers produce. As always we measured at a room temperature of 21-22 Degrees C.

table_tl.gif

blank.gif

table_tr.gif
blank.gif BFG GeForce 9800 GTX OCX  review blank.gif
table_bl.gif blank.gif table_br.gif

In idle mode you'll notice fine cooling performance; expect a temperature of 55 Degrees C when the GPU idles (desktop mode). And during gaming when heat builds up, heavily stressed the GPU core temperature rose towards roughly 70 Degrees C. It's 100% equal to the reference GTX's we recently tested, so despite the faster clock speeds there is no real increase in heat levels. Which is awesome.

Share this content
Twitter Facebook Reddit WhatsApp Email Print