As most of you know, with most videocards you can apply a simple series of tricks to boost the overall performance a little. You can do this at two levels, namely tweaking by enabling registry or BIOS hacks, or very simply by tampering with Image Quality. And then there is overclocking, which will give you the best possible results by far.
What do we need? One of the best tools for overclocking NVIDIA and ATI videocards is our own AfterBurner which will work with 90% of the graphics cards out there. We can really recommend it, download here.
Where should we go? Overclocking: By increasing the frequency of the videocard's memory and GPU, we can make the videocard increase its calculation clock cycles per second. It sounds hard, but it really can be done in less than a few minutes. I always tend to recommend to novice users and beginners, to not increase the frequency any higher than 5% on the core and memory clock. Example: If your card runs at 600 MHz (which is pretty common these days) then I suggest that you don't increase the frequency any higher than 30 to 50 MHz.
More advanced users push the frequency often way higher. Usually when your 3D graphics start to show artifacts such as white dots ("snow"), you should back down 10-15 MHz and leave it at that. Usually when you are overclocking too hard, it'll start to show artifacts, empty polygons or it will even freeze. Carefully find that limit and then back down at least 20 MHz from the moment you notice an artifact. Look carefully and observe well. I really wouldn't know why you need to overclock today's tested card anyway, but we'll still show it.
All in all... do it at your own risk.
Core Clock: 800 MHz
Core Clock: 880 MHz
Core Clock: 1150 MHz
Shader Clock: 800 MHz
Shader Clock: 880 MHz
Shader Clock: 1150 MHz
Memory Clock: 5000 MHz
Memory Clock: 5000 MHz
Memory Clock: 6216 MHz
Open up AMD overdrive. Now we need to free the card up from TDP restrictions first, so all the way down move the Power control settings slider towards 20%.
Overclocking wise the card will allow itself to be clocked to roughly 1000~1040 MHz on the core. And that's without additional voltage tweaking. Voltage tweaking will definitely get you higher.
We applied extra voltage with MSI AfterBurner though, increasing the core to 1225 Mv; 50% Fan RPM gave us a cool 1150 MHz on the core. The memory can be clocked towards 1554 stable, with a quad data-rate that becomes 6216 MHz.
And that brings us to a completely stable overclock, and that is very impressive. The GPU was getting slightly warmer as we reached 80 Degrees C. The noise level went slightly up, nothing too bad though.
These are the results of our overclock:
Above, Crysis 2, same maxed out image quality settings as before yet now with added overclock results:
High Resolution Texture Pack
Ultra Quality settings
Level - Times Square (2 minute custom time demo)
Above, 3DMark 11 - the Performance test and score. As you can see, there is an additional bump in this very GPU limited software, lovely.
Above, Alien versus Predator, in 1920x1200 at 4xAA and 16X anisotropic filtering
PowerColor Radeon R9-290X PCS+ review PowerColor Radeon R9-290X PCS+ review - this beast runs at low temperatures whilst being factory overclocked. The 2816 Stream processor based Hawaii chip will get paired with 4 GB...
PowerColor Radeon HD 7850 SCS3 review We test and review the PowerColor Radeon HD 7850 SCS3 today. This stock clocked Radeon HD 7850 is cooled passively, meaning it has no fans tool it down. That also means it's rather silent as it does not make any noise. But what about temperatures then you must be wondering ?
PowerColor 7790 TurboDuo OC review We test and review the PowerColor Radeon HD 7790 TurboDuo OC edition incl FCAT Frametimes. The new graphics card is intended to boost a little more performance into entry-level gaming. The PowerColor TurboDuo HD7790 OC clocks at 7.5% overclocking speed on boost engine, packed with dual-fan cooling and S-shape heat pipe direct touch technology.
PowerColor Radeon HD 7950 PCS+ review PowerColor is the first in our line-up of R7950 reviews with a customized model. It is the PCS version that clocks in at a cool 880 MHz on the graphics core with it's memory clocked default at an effective data rate of 5000 MHZ. Armed witha custom cooler it is silent, and even cooler compared to the reference model.