Installation of any GeForce graphics card is really easy. Once the card is installed and seated into the PC, we connect the 6-pin PEG power connector to the graphics card. Preferably your power supply is compatible, most high-end PSUs built after the year 2008 have these connectors as standard.
So preferably the PEG headers should come directly from the power supply and are not converted from 4-pin Molex peripheral connectors. Don't forget to connect your monitor, you can now turn on your PC, boot into Windows, install the latest compatible NVIDIA GeForce Forceware driver and after a reboot all should be working. No further configuration is required or needed.
Let's have a look at how much power draw we measure with this graphics card installed.
The methodology: We have a device constantly monitoring the power draw from the PC. We simply stress the GPU, not the processor. The before and after wattage will tell us roughly how much power a graphics card is consuming under load.
Our test system is based on a power hungry Core i7 - X79 system. This setup is overclocked to 4.60 GHz on all cores. Next to that we have energy saving functions disabled for this motherboard and processor (to ensure consistent benchmark results). On average we are using roughly 50 to 100 Watts more than a standard PC due to higher CPU clock settings, water-cooling, additional cold cathode lights etc.
We'll be calculating the GPU power consumption here, not the total PC power consumption.
Measured power consumption single card
System in IDLE = 99 W
System Wattage with GPU in FULL Stress = 226W
Difference (GPU load) = 127 W
Add average IDLE wattage ~10W
Subjective obtained GPU power consumption = ~ 137 Watts
Mind you that the system wattage is measured at the wall socket side and there are other variables like PSU power efficiency. So this is a calculated value, albeit a very good one.
Above, a chart of relative power consumption. Again the Wattage shown is the card with the GPU(s) stressed 100%, showing only the peak GPU power draw, not the power consumption of the entire PC and not the average gaming power consumption.
Here is Guru3Ds power supply recommendation:
GeForce GTX 650 Ti Boost - On your average system the card requires you to have a 500 Watt power supply unit.
GeForce GTX 650 Ti Boost SLI - On your average system the card requires you to have a 650 Watt power supply unit.
If you are going to overclock GPU or processor, then we do recommend you purchase something with a bit more stamina.
There are many good PSUs out there, please do have a look at our many PSU reviews as we have loads of recommended PSUs for you to check out in there. What would happen if your PSU can't cope with the load:
bad 3D performance
spontaneous reset or imminent shutdown of the PC
freezing during gameplay
PSU overload can cause it to break down
Let's move to the next page where we'll look into GPU heat levels and noise levels coming from this graphics card.
Palit GeForce GTX 950 Storm X Dual 2GB review In this review we check out the 2GB version of the Palit GeForce GTX 950. The GTX 950 is the entry-level to mainstream graphics card in the Maxwell range of GPUs from Nvidia. Palit offers it in a Stor...
Palit GeForce GTX 980 Ti Super Jetstream Review In this review we benchmark the new Palit GeForce GTX 980 Super Jetstream, a product that will command and conquer as it offers massive game rendering performance at 100% quiet nose levels. Hey and it...
Palit GeForce GTX 960 Super JetStream review In this review we check out the Palit GeForce GTX 960 Super JetStream. This product is in the top 3 of best GTX 960 cards as it is performing the fastest, it is the most silent one, and it has just go...
Palit GeForce GTX 980 Super Jetstream review We review one of the fastest GeForce GTX 980 cards from Palit, the Super Jetstream edition. It comes all customized, has an improved Jetstream series cooler and runs factory tweaked at clock frequenci...