A smaller 28nm based chip means you can do more with less as the product becomes smaller, the GK104 GPU comes with roughly 3.54 billion transistors embedded into it. The TDP (maximum board power) sits at a very respectable 150 Watts. So in one hand you have a graphics card that uses less power, yet offers more performance. That's always a win.
The GeForce GTX 660 Ti will be released with two 6-pin power connectors to get enough current and a little spare for overclocking. This boils down as: 2x 6-pin PEG = 150W + PCIe slot = 75W is 225W available (in theory). We'll measure all that later on in the article but directly related is the following chapter.
Dynamic Clock Adjustment technology
Kepler GPU will feature a Dynamic Clock Adjustment technology and we can explain it easily without any complexity. Typically when your graphics card idles the cards clock frequency will go down... yes? Well, obviously Kepler architecture cards will do this as well, yet now it works vice versa as well. If in a game the GPU has room left for some more, it will increase the clock frequency a little and add some extra performance. You could say that the graphics card is maximizing it's available power threshold.
Even more simple, DCA resembles Intels Turbo Boost technology a little bit by automatically increasing the graphics core frequency with 5 to 10 percent when the card works bellow its rated TDP.
The baseclock of the Reference GeForce GTX 660 in 3D mode is 915 MHz, but it can boost towards 980 MHz. For the different SKUs from board partners these numbers will be different.
The 'Boost Clock' however is directly related to the maximum board power, so it might clock even higher as longs as the GPU sticks within it's power target. Overclocking on that end will work the same as GPU boost will continue to work while overclocking, it stays restricted within the TDP bracket. We'll show you that in our overclocking chapter.
3D Vision surround on a Single GPU
Whether or not NVIDIA would like to admit it, ATI's Eyefinity certainly changed the way we all deal with multi-monitor setups. As a result in the series 500 products there was multi monitor support for gaming with three monitors, this is called Surround Vision. The downside here was that you needed at least two cards setup in SLI for this to work.
It would not have made any sense to have not addressed this with Kepler, so Surround vision and 3D Surround vision are now supported with one card That means you can game even in 3D on three monitors with just one GeForce GTX 680 as the new display engine can drive four monitors at once. Keplers display engine fully supports HDMI 1.4a, 4K monitors (3840x2160) and multi-stream audio.
Using up-to 4 displays
We just had a quick chat about 3D Vision surround but Kepler goes beyond three monitors. You can connect four monitors, use three for gaming and setup one top side (3+1) monitor to check your email or something desktop related.
Summing up Display support
3D Vision Surround running off single GPU
Single GPU support for 4 active displays
DisplayPort 1.2, HDMI 1.4a high speed
4K monitor support - full 3840x2160 at 60 Hz
In combination with new Desktop management software you can also tweak your desktop output a little like center your Window taskbar at the middle of the three monitors or maximize windows to a single display. With the software you can also setup and apply bezel correction. Interesting though is a new feature that allows you to use hotkeys to see game menu's hidden by the bezel.
PCIe Gen 3
The series 600 cards from NVIDIA all are PCI Express Gen 3 ready. This update provides a 2x faster transfer rate than the previous generation, this delivers capabilities for next generation extreme gaming solutions. So opposed to the current PCI Express slots which are at Gen 2, the PCI Express Gen 3 will have twice the available bandwidth and that is 32GB/s, improved efficiency and compatibility and as such it will offer better performance for current and next gen PCI Express cards.
To make it even more understandable, going from PCIe Gen 2 to Gen 3 doubles the bandwidth available to the add-on cards installed, from 500MB/s per lane to 1GB/s per lane. So a Gen 3 PCI Express x16 slot is capable of offering 16GB/s (or 128Gbit/s) of bandwidth in each direction. That results in 32GB/sec bi-directional bandwidth.
MSI GeForce GTX 980 Ti Lightning Review Thunderclouds hover above the Guru3D test-lab as the MSI GeForce GTX 980 Ti Lightning edition will now get a review. Yes we test and benchmark one of the most anticipated GeForce GTX 980 Ti cards of ...
MSI GeForce GTX 950 Gaming + 2-way SLI review We review the MSI GeForce GTX 950 Gaming (in SLI as well), this entry-level to mainstream graphics card is armed with a GM206 Maxwell generation graphics processor from Nvidia. The product performs qu...
MSI GeForce GTX 980 Ti Gaming OC Review In this review we benchmark the new MSI GeForce GTX 980 Ti Gaming (OC edition), the product is really good, awesome cooling, totally silent, it's factory overclocked and combined with the default var...
MSI GeForce GTX 960 Gaming OC review We review the MSI GeForce GTX Gaming OC, the card comes with a newly revised TwiNFrozr model cooler. And that makes it silent and deadly as you will not hear this product. The GTX 960 is introduced in th...