HIS Radeon HD 4870 X2 2048MB review
Posted by Hilbert Hagedoorn on: 10/29/2008 02:00 PM [ 0 comment(s) ]
Setting up the PC
Installing a Radeon 4870 X2 into your system will be a pretty easy job. Just slide the card into a free PCIe slot, connect one 6-pin and one 8-pin power connector to the card (if either one is missing, the card will not work). I expect AIBs to include a 6 to 8-pin power converter cable by the way. HIS did not do this, a little disappointing really.
I do recommend you to just buy a high-end PSU with both connectors on there anyway. Cable management alone would make that look much nicer. Bare in mind though that the board is lengthy, 27 CM. Make sure nothing is blocking/obstructing the product.
Once the card is installed we startup windows. We installed our driver, rebooted and that was it. With a single X2 there's no need to tag Crossfire active in the drivers or anything. The card will work straight out of the box. Just the way we like it.
Quick and easy.
It's time to do some actual testing with these card. We'll start off by showing you some tests we have done on overall power consumption of the PC. Looking at it from a performance versus wattage point of view, the power consumption is really good with the new 55nm products.
Our test system contains a Core 2 Duo E8400 Processor @ 3.0 GHz (FSB 1333), the ASUS P5E3 Deluxe mainboard, stock cooling on the CPU, DVD-rom and a WD Raptor drive. The results:
System Under FULL load
|Radeon HD 4850||269 Watt|
|Radeon HD 4870||334 Watt|
|Radeon HD 4850 Crossfire||421 Watt|
|Radeon HD 4870 X2 (HIS)||423 Watt|
The monitoring device is reporting a maximum system wattage peak at roughly 422-430 Watts with 2-way 4870 embedded on the X2.
Power supply wise I recommend at the very least, 600 Watts. You might not utilize all that power distribution, yet especially in this high-end game make sure you have some reserves folks. You do not want your PSU to run at it's maximum all of the time. See, it's not that your PC will consume that much power, it's just that you want to make sure your PSU can deal with the hefty load and will stay stable during you entire gaming experience.
Please make note of the fact that the card uses one 6-pin PCIe power connector and one 8-pin connector.
Inevitably people will opt CrossfireX and go with a 4-GPU based model. With two cards obviously 1000+ Watt power supplies are recommended, and in fact even needed to be able to even supply something as simple as enough PCIe graphics power connectors. We passed 700 Watts, which is just too much to play games folks. We used a Galaxy 1000 Watt DDX PSU by the way, perfectly stable.
There are many good PSU's available, over the years we reviewed a lot of them and have loads of recommended PSU's for you to check out in there, have a look. Things that can happen if your PSU can't cope with the load?:
- bad 3D performance
- crashing games
- spontaneous reset or imminent shutdown of the PC
- freezes during gameplay
- PSU overload can cause it to break down
The thermal envelope
Our Rivatuner application currently is under development for more precise thermal monitoring, yet we were able to monitor heat levels from both GPUs pretty well.
|Temperature in degrees C||Idle||Peak|
Our new HIS 4870 X2 sample shows idle temps are roughly 70-75 Degrees C. Yet when the GPUs are fully utilized & stressed it reached nearly 85 Degrees C. It's a known act by now, the peak thermals on the entire 4800 series are really high. Now the product can take it fine, it is just a lot to digest.
The good thing with the X2 is that the cooler is dual-slot, and uses the colder air inside your PC to cool down the GPUs and then blows it away (exhausts) it at the rear of the card, outside of the PC.
A lot and I do mean a LOT of heat is disposed outside the PC by the 4870 X2. Here's something to think about. If you game long enough in Crossfire, a small room will actually warm up. I'm not kidding.
When graphics cards produce a lot of heat, that heat usually needs to be transported away from the hot core as fast as possible. Often you'll see massive active fan solutions that can indeed get rid of the heat, yet all the fans these days make the PC a noisy son of a gun. I'm doing a little try-out today with noise monitoring, so basically the test we do is extremely subjective. We bought a certified dBA meter and will start measuring how many dBA originate from the PC. Why is this subjective, you ask? Well, there is always noise in the background, from the streets, from the HD, PSU fan etc etc, so this is by a mile or two not a precise measurement. You could only achieve objective measurement in a sound test chamber.
The human hearing system has different sensitivities at different frequencies. This means that the perception of noise is not at all equal at every frequency. Noise with significant measured levels (in dB) at high or low frequencies will not be as annoying as it would be when its energy is concentrated in the middle frequencies. In other words, the measured noise levels in dB will not reflect the actual human perception of the loudness of the noise. That's why we measure the dBa level. A specific circuit is added to the sound level meter to correct its reading in regard to this concept. This reading is the noise level in dBA. The letter A is added to indicate the correction that was made in the measurement. Frequencies below 1kHz and above 6kHz are attenuated, where as frequencies between 1kHz and 6kHz are amplified by the A weighting.
|TYPICAL SOUND LEVELS|
|Jet takeoff (200 feet)||120 dBA|
|Construction Site||110 dBA||Intolerable|
|Shout (5 feet)||100 dBA|
|Heavy truck (50 feet)||90 dBA||Very noisy|
|Urban street||80 dBA|
|Automobile interior||70 dBA||Noisy|
|Normal conversation (3 feet)||60 dBA|
|Office, classroom||50 dBA||Moderate|
|Living room||40 dBA|
|Bedroom at night||30 dBA||Quiet|
|Broadcast studio||20 dBA|
|Rustling leaves||10 dBA||Barely audible|
We start up a benchmark and leave it running for a while. The fan rotational speed remains constant. We take the dBA meter, move away 75 CM and then aim the device at the active fan on the graphics card.
Noise levels are becoming pretty standard these days, again we see both the coolers from the two products make more noise once it needs to cool down more (RPM spins up) though audible it's not bad though.
At idle (desktop mode) you'll hardly hear the card, the FAN RPM is pretty low and results in an overall DBA level of less than 40, which is actually great. The minute though the GPUs start to heat up, the RPM of the fan will increase and you can expect roughly 43 DBa when the GPU is fully stressed for both cards.
So you'll likely you'll hear the fan blowing during gaming, but really that's not too loud at all. No problem there.
We test and review the a HIS Radeon HD 7950 HIS IceQ X, this 30 CM sized beast is one heck of a graphics card. Custom PCB, custom cooling, it's low noise and being a Boost edition card series, it clocks in at 950 MHz.
HIS Radeon HD 7850 4GB iPower IceQ Turbo review
We test and review the a HIS Radeon HD 7850 iPower IceQ Turbo as single card and in Crossfire today. The HIS Radeon HD 7850 iPower IceQ Turbo is a factory overclocked 4GB version of the Radeon HD 7850 graphics card.
HIS Radeon HD 7970 X Turbo edition review
We review the HIS Radeon HD 7970 X Turbo edition. With this card they took the new Tahiti XT2 and redesigned the R7970 board from ground up. though very long the end result is a 31cm PCB with mane power phases and optimizations. Fun to see are the voltage and FAN monitor LED options. Most impressive however is the sheer amount of monitor connectors HIS injected into this product, four DisplayPort connectors, one HDMI and a DVI connector. If needed you can go for Eyefinity6. Oh did I mention already that the factory set boost clock frequency is 1180 Mhz ?
HIS Radeon HD 7950 ICEQ Turbo review
We review the HIS Radeon HD 7950 IceQX Turbo. The product comes factory overclocked very nicely for you as it is running a gentle 900 MHz clock frequency. HIS uses a custom PCB and dual-slot cooler making the card very easy to install. Despite that factory overclock and that cooler the noise levels remain at very low levels whereas the GPU temperatures remain downright excellent as we'll show you in this review.