HIS Radeon 6850 & 6870 review -
Overclocking the HIS R6870
Overclocking the HIS R6870
As most of you know, with most videocards you can apply a simple series of tricks to boost the overall performance a little. You can do this at two levels, namely tweaking by enabling registry or BIOS hacks, or very simply to tamper with Image Quality. And then there is overclocking, which will give you the best possible results by far.
What do we need?
One of the best tools for overclocking NVIDIA and ATI videocards is our own Rivatuner. If you own an ATI or NVIDIA graphics card then the manufacturer actually has some very nice built in options for you that can be found in the display driver properties. Based on Rivatuner you can alternatively use MSI AfterBurner which will work with 90% of the graphics cards out there. We can really recommend it, download here.
Where should we go?
Overclocking: By increasing the frequency of the videocard's memory and GPU, we can make the videocard increase its calculation clock cycles per second. It sounds hard, but it really can be done in less than a few minutes. I always tend to recommend to novice users and beginners, to not increase the frequency any higher than 5% on the core and memory clock. Example: If your card runs at 600 MHz (which is pretty common these days) then I suggest that you don't increase the frequency any higher than 30 to 50 MHz.
More advanced users push the frequency often way higher. Usually when your 3D graphics start to show artifacts such as white dots ("snow"), you should back down 10-15 MHz and leave it at that. Usually when you are overclocking too hard, it'll start to show artifacts, empty polygons or it will even freeze. Carefully find that limit and then back down at least 20 MHz from the moment you notice an artifact. Look carefully and observe well. I really wouldn't know why you need to overclock today's tested card anyway, but we'll still show it.
All in all... do it at your own risk.
|Core Clock: 900 MHz||Core Clock: 900 MHz||Core Clock: 964 MHz|
|Shader Clock: 900 MHz||Shader Clock: 900 MHz||Shader Clock: 964 MHz|
|Memory Clock: 4200 MHz||Memory Clock: 4200 MHz||Memory Clock: 4752 MHz|
Now, we left the fan RPM control at default in all circumstances. We reached a very decent overclock guaranteeing better results. Voltage tweaking is not yet an option. With AfterBurner (download here) our stable end result was roughly 965 MHz on the core and 4752 MHz on the memory.
Here we have the card with Call of Duty: Modern Warfare 2, maxed out image quality settings as before with 4xAA 16xAF, keep in mind that the light blue bar represents baseline 6870 performance and the bright orange one the overclocked performance. It's roughly another 5 to 10% performance totally for free.
As you can see, the increased clock did not offer that much extra performance, we see this quite a bit with high-end ATI products.
We test and review the a HIS Radeon HD 7950 HIS IceQ X, this 30 CM sized beast is one heck of a graphics card. Custom PCB, custom cooling, it's low noise and being a Boost edition card series, it clocks in at 950 MHz.
HIS Radeon HD 7850 4GB iPower IceQ Turbo review
We test and review the a HIS Radeon HD 7850 iPower IceQ Turbo as single card and in Crossfire today. The HIS Radeon HD 7850 iPower IceQ Turbo is a factory overclocked 4GB version of the Radeon HD 7850 graphics card.
HIS Radeon HD 7970 X Turbo edition review
We review the HIS Radeon HD 7970 X Turbo edition. With this card they took the new Tahiti XT2 and redesigned the R7970 board from ground up. though very long the end result is a 31cm PCB with mane power phases and optimizations. Fun to see are the voltage and FAN monitor LED options. Most impressive however is the sheer amount of monitor connectors HIS injected into this product, four DisplayPort connectors, one HDMI and a DVI connector. If needed you can go for Eyefinity6. Oh did I mention already that the factory set boost clock frequency is 1180 Mhz ?
HIS Radeon HD 7950 ICEQ Turbo review
We review the HIS Radeon HD 7950 IceQX Turbo. The product comes factory overclocked very nicely for you as it is running a gentle 900 MHz clock frequency. HIS uses a custom PCB and dual-slot cooler making the card very easy to install. Despite that factory overclock and that cooler the noise levels remain at very low levels whereas the GPU temperatures remain downright excellent as we'll show you in this review.