As most of you know, with most video cards you can apply a simple series of tricks to boost the overall performance a little. You can do this at two levels, namely tweaking by enabling registry or BIOS hacks, or very simply to tamper with Image Quality. And then there is overclocking, which will give you the best possible results by far.
What do we need? One of the best tools for overclocking NVIDIA and ATI videocards is our own AfterBurner which will work with 90% of the graphics cards out there. We can really recommend it, download here.
Where should we go? Overclocking: By increasing the frequency of the videocard's memory and GPU, we can make the videocard increase its calculation clock cycles per second. It sounds hard, but it really can be done in less than a few minutes. I always tend to recommend to novice users and beginners, to not increase the frequency any higher than 5% on the core and memory clock. Example: If your card runs at 600 MHz (which is pretty common these days) then I suggest that you don't increase the frequency any higher than 30 to 50 MHz.
More advanced users push the frequency often way higher. Usually when your 3D graphics start to show artifacts such as white dots ("snow"), you should back down 10-15 MHz and leave it at that. Usually when you are overclocking too hard, it'll start to show artifacts, empty polygons or it will even freeze. Carefully find that limit and then back down at least 20 MHz from the moment you notice an artifact. Look carefully and observe well. I really wouldn't know why you need to overclock today's tested card anyway, but we'll still show it.
All in all... do it at your own risk.
Core Clock: 980 MHz
Core Core Clock: 1033 MHz
Core Clock: +50 MHz
Boost Clock: 1033 MHz
Boost Clock: 1098 MHz
Boost Clock: ~1200 MHz
Memory Clock: 6008 MHz
Memory Clock: 6008 MHz
Memory Clock: 6696 MHz
Now with the Dynamic boost function of the series 600 cards overclocking is definitely more complicated to work with. It remains simple enough though if you know what and how to do it.
In your favorite overclock utility of choice you widen up the TDP limitations a bit, set the power limiter towards 110% (unfortunately it is the maximum for this card). That way the Dynamic boost function won't down clock all the time to meet its upper threshold in TDP limitations.
We now add another 50 MHz towards the graphics core (that was the maximum stable on the of the factory-overclock), normally we'd add and increase Voltage with a +100 Mv but that feature was not yet working in the overclocking software. We now are hovering at 1200 MHz (which varies based on power draw/load/changes) on the overclock.
With a the physical board power limit you are going see all card roughly ending at this overclock and boost frequency. For the memory we ended at +350 MHz which is almost 6696 MHz (effective data rate). At this stage the cooler RPM was set at default which kept the noise levels under control at 38~39 DBa and thus remains silent.
We now have a hint extra performance at our hands on top of the factory overclock, have a peek at the results when overclocked.
Above, Crysis 2, same maxed out image quality settings as before yet now with added overclock results:
High Resolution Texture Pack
Ultra Quality settings
Level - Times Square (2 minute custom time demo)
Above, 3DMark 11 - the Performance test and score. As you can see, there is an additional bump in this very GPU limited software, lovely. Also compare it with a reference GTX 680 results, that's roughly 2500 point away only. Mind you that GTX 660 Ti, 670 and GTX 680 overclock as well, so try to keep things in perspective.
Above, Alien versus Predator, in 1920x1200 at 4xAA and 16X anisotropic filtering
Gigabyte GeForce GTX 750 Ti WindForce review In this review we take the Gigabyte GeForce GTX 750 Ti WindForce for a spin. The card is obviously based on NVIDIAs MAxwell based GTX 750 Ti GPU. Gigabyte designed their own PCB, tweaked the card a h...
Gigabyte Radeon R9-290X WindForce 3X OC review We review the Gigabyte Radeon R9-290X WindForce 3X OC edition. A lot of you guys have been waiting on a custom cooled version of this product. Armed with the latest revision of the WindForce 3X cooler and will get that 2816 Stream processor ...
Gigabyte Uranium game mouse review We review the Gigabyte Uranium game mouse, the device is unique in the sense that is comes with an OLED display POD that will inform you of your mouse polling rate, DPI or even battery status. The hig...
Gigabyte G1.Sniper B5 review Let's review the Gigabyte G1.Sniper B5, which is based on the budet B85 chipset from Intel. See B85 based motherboards typically end up in business desktops and normally are limited from overclocking. Well, that changes with the Gigabyte G1.Sniper B5 ! So small price, nice features and tweakability ? We just have to check that out. Oh and you'll get many USB 3.0 ports and of course an improved and enhanced audio solution (albeit that really is a software layer sitting on top of the Realtek ALC 898 codec). Be sure to check out this review.