As most of you know, with most video cards you can apply a simple series of tricks to boost the overall performance a little. You can do this at two levels, namely tweaking by enabling registry or BIOS hacks, or very simply to tamper with Image Quality. And then there is overclocking, which will give you the best possible results by far.
What do we need? One of the best tools for overclocking NVIDIA and ATI videocards is our own AfterBurner which will work with 90% of the graphics cards out there. We can really recommend it, download here.
Where should we go? Overclocking: By increasing the frequency of the videocard's memory and GPU, we can make the videocard increase its calculation clock cycles per second. It sounds hard, but it really can be done in less than a few minutes. I always tend to recommend to novice users and beginners, to not increase the frequency any higher than 5% on the core and memory clock. Example: If your card runs at 600 MHz (which is pretty common these days) then I suggest that you don't increase the frequency any higher than 30 to 50 MHz.
More advanced users push the frequency often way higher. Usually when your 3D graphics start to show artifacts such as white dots ("snow"), you should back down 10-15 MHz and leave it at that. Usually when you are overclocking too hard, it'll start to show artifacts, empty polygons or it will even freeze. Carefully find that limit and then back down at least 20 MHz from the moment you notice an artifact. Look carefully and observe well. I really wouldn't know why you need to overclock today's tested card anyway, but we'll still show it.
All in all... do it at your own risk.
Core Clock: 1058 MHz
Core Core Clock: 1124 MHz
Core Clock: +150 MHz / 1274 MHz
Memory Clock: 5000 MHz
Memory Clock: 5000 MHz
Memory Clock: 5900 MHz
We now add another 150 MHz towards the graphics core (that was the maximum stable on the of the factory-overclock). We now are now at 1275 MHz already.
With a the physical board power limit you are going see all card roughly ending at this overclock and boost frequency. For the memory we ended at 5900 MHz. At this stage the cooler RPM was set at default which kept the noise levels under control at 38~39 DBa and thus silent.
We now have a hint extra performance at our hands on top of the factory overclock, have a peek at the results when overclocked.
Above, Crysis 2, same maxed out image quality settings as before yet now with added overclock results:
High Resolution Texture Pack
Ultra Quality settings
Level - Times Square (2 minute custom time demo)
Above, 3DMark 11 - the Performance test and score. As you can see, there is an additional bump in this very GPU limited software, lovely. Also compare it with a reference GTX 680 results, that's roughly 2500 point away only. Mind you that GTX 660 Ti, 670 and GTX 680 overclock as well, so try to keep things in perspective.
Above, Alien versus Predator, in 1920x1200 at 4xAA and 16X anisotropic filtering
MSI GeForce GTX 1070 Aero ITX OC Review In this article we'll review the MSI GeForce GTX 1070 Aero ITX 8G OC. Aimed at the small form factor DiY PC gamer, this somewhat budget graphics card launches at roughly € 449,- / USD, the s...
GeForce GTX 1080 Ti Review In this article we'll look at the fastest graphics card your money can get you, the Nvidia GeForce GTX 1080 Ti based on Pascal architecture. Armed with 11GB of GDDR5X graphics memory and that all ne...
Palit GeForce GTX 1050 Ti KalmX Review In this article we'll review the passively cooled Palit GeForce GTX 1050 Ti KalmX, the graphics cards has no fans, just one big cooling radiator and is positioned at the budget minded consumer these ...
MSI GeForce GTX 1060 Aero ITX Review In this article we'll review the MSI GeForce GTX 1060 Aero ITX 6B, aimed at the small form factor DiY PC gamer this somewhat budget graphics card launches at roughly 249 USD, the smallest GTX 1060 y...