One of the hip features of the X79 / SBE platform is quad-channel memory. Make no mistake, back in 2008 we already discovered (and reported) in whitepapers that the Nehalem architecture was quad-channel ready, they just never implemented it. But with triple-channel performance as good as it is, that was wishful thinking anyway.
Though nothing has been as rock solid as Intel's 64-bit memory controllers a lot certainly happened. Over the space of three years we went from dual-channel towards triple-channel on X58 (Gulftown), then back to dual-channel with the Sandy Bridge architecture and now with Sandy Bridge-E we see quad-channel memory support. Regardless of what you think about it, progress is obviously always a good thing.
Admittedly, the Intel memory controller, whatever platform you choose, is excellent. Sandy Bridge and its dual-channel controller hauls ass, make no mistake there. At launch quad-channel 1600 MHz low-voltage DDR3 is supported out of the box, and that means an increase from 25.6 GB/s to 51.2 GB/s of available memory bandwidth. That's fast enough to drive a mid-range graphics card ported through system memory fairly well, well if we exclude latency of course.
Quad-channel is going to be crazy stuff, crazy numbers is what you'll see. What the effect will be on real-world performance, well yes... that's trivial at best.
More PCIe lanes
The one thing that people grumble about the most with P67/Z68 is the relatively small number of available PCIe lanes (16) for graphics cards. If you are using a setup with two or more graphics cards (SLI/Crossfire), the PCIe bandwidth is limited at x8:x8. Here again the performance difference is trivial as running today's fastest cards barely utilizes all that bandwidth, but two x16 and then room for another x8 obviously is much better.
Sandy Bridge-E has a nice 40 lanes available. You can split them up in a variety of combinations, two x16 links with one x8 link, one x16 link and three x8 links, or one x16 link, two x8 links, and two x4 links. So this will be one concern less, though I betcha some of you would like to see three x16 as an option.
PCIe gen 3.0
What should be a prominent feature of the X79 chipset update is the inclusion of PCI Express Gen 3. In a nutshell, PCI Express Gen 3 provides a 2X faster transfer rate than the previous generation, this delivers capabilities for next generation extreme gaming solutions.
Right now we are still disputing the fact that PCIe Gen 3 is working properly, we hear the same thing from several manufacturers. However, with no Gen 3 video cards at hand it is impossible to test and check. If it doesn't work then it might get fixed/enabled with future BIOS updates or... Intel might have scrapped it from the feature list and is bringing it as a feature to Ivy Bridge. For now, however, this remains unconfirmed.
Regardless, we love to explain stuff; PCI Express Gen 3 has twice the available bandwidth, 32GB/s, improved efficiency and compatibility and as such it will offer better performance for current and next gen PCI Express cards. Going from PCIe Gen 2 to Gen 3 doubles the bandwidth available to the add-on cards installed, from 500MB/s per lane to 1GB/s per lane.
So a Gen 3 PCI Express x16 slot is capable of offering 16GB/s (or 128Gbit/s) of bandwidth in each direction. That results in 32GB/sec bi-directional bandwidth.
Again, the big problem is that to date there really is nothing here in the lab we can use to test these new slots. You need proper compatible hardware, like this platform, but also a graphics card or say PCIe SSD supporting the new standard.
It is a little unfortunate that once again we see a new socket with this processor series. Over the last three years we left LGA 775 then started with LGA 1366, then moved to LGA 1156, with Sandy Bridge we moved to LGA 1155 and now we have to harbor the processor in socket LGA 2011.
We know, it's unfortunate, but with a changed architecture and features like the quad-channel memory controller, the lack of an embedded graphics unit and the massive update towards 40 PCIe lanes the entire dynamic changed. So ever since 2008 that's four different CPU sockets in the consumer market.
It's not a weird move to make, but for those on LGA 1155 hoping to upgrade to Sandy Bridge-E on the same motherboard, well it's not a possibility.
So yes, this means that for a Sandy Bridge-E processor you'll need to purchase an accompanying motherboard based on the X79 chipset. Not just that though, the cooler mounting is completely different as well, you'll need to seek a new mounting bracket for your cooler, or purchase an LGA 2011 compatible cooler.
An Optional Liquid CPU Cooler
Next to AMD Intel has plans to sell special kits of the high-performance Sandy Bridge-E processors that in addition of the CPU will also include an Intel branded closed loop liquid cooler. This is the first time that the chip maker will bundle any of its processors with a water cooling solution.
In addition to selling the liquid cooler as part of a kit, Intel also plans to release this solution separately. The CPU water cooler is made and built together with Asetek, a maker well renowned for its high-quality closed loop liquid coolers, and includes a water block and pump assembly that goes on top of the CPU and a 120mm radiator with a pre-fitted fan.
Both the pump and the fan were designed to feature blue illumination, which closely resembles the color of the Intel logo. The Intel branded Liquid Cooling Solution can be found under SKU code RTS2011LC.
Core i7 6700K processor review: Desktop Skylake We review the Skylake Intel Core i7 6700K flagship quad-core processor fabbed at a 14nm node. This little puppy is fast, agile and in full attack mode - but will it be worth an upgrade over the previo...
Core i7 5775C processor review: Desktop Broadwell We review the Intel Core i7 5775C processor developed at a 14nm node these processors are a notch more energy friendly. Join us as we look at the performance of this processor in a wide variety of ben...