Installation of any of the AMD Radeon cards is really easy. Once the card is seated into the PC make sure you hook up the monitor and of course any external power connectors like 6 and/or 8-pin PEG power connectors. Preferably get yourself a power supply that has these PCIe PEG connectors native (converting them from a Molex Peripheral connector anno 2011 we feel is a no-go).
For the two cards, make sure you seat the card in the highest available PCIe slots (x8/x16), and bridge them with the crossfire connector. We've shown you that in a previous chapter in this article.
Once done, we boot into Windows, install the latest ATI Catalyst drivers and after a reboot all should be working. In the Catalyst Control Software make sure CrossfireX is enabled. No further configuration is required or needed unless you like to tweak the settings, for which you can open the Catalyst Control Center.
Let's have a look at how much power draw we measure with this graphics card installed.
The methodology: We have a device constantly monitoring the power draw from the PC. We simply stress the GPU, not the processor. The before and after wattage will tell us roughly how much power a graphics card is consuming under load.
Note: there has been a lot of discussion using FurMark as stress test to measure power load. Furmark is so malicious on the GPU that it does not represent an objective power draw compared to really hefty gaming. If we take a very-harsh-on-the-GPU gaming title, then measure power consumption and then compare the very same with Furmark, the power consumption can be 50 to 100W higher on a high-end graphics card solely because of FurMark.
We decided to move away from Furmark in early 2011 and are now using a game like application which stresses the GPU 100% yet is much more representable of power consumption and heat levels coming from the GPU. We however are not disclosing what application that is as we do not want AMD/ATI/NVIDIA to "optimize & monitor" our stress test whatsoever, for our objective reasons of course.
Our test system is based on a power hungry Core i7 965 / X58 system. This setup is overclocked to 3.75 GHz. Next to that we have energy saving functions disabled for this motherboard and processor (to ensure consistent benchmark results). On average we are using roughly 50 to 100 Watts more than a standard PC due to higher CPU clock settings, water-cooling, additional cold cathode lights etc.
We'll be calculating the GPU power consumption here, not the total PC power consumption.
Measured power consumption for two cards in Crossfire
System in IDLE = 166W
System Wattage with GPU in FULL Stress = 567W
Difference (GPU load) = 401W
Add average IDLE wattage ~6W
Subjective obtained GPU power consumption = ~ 407 Watts
Mind you that the system wattage is measured at the wall socket.
TDP in KWh
2 hrs day
4 hrs day
Graphics card measured TDP
Cost 5 days per week / 4 hrs day
Cost per Month
Cost per Year 5 days week / 4 hrs day /
Cost per Year 5 days week / 4 hrs day / $
We estimate and calculate here based on four hours GPU intensive gaming per day for 5 days a week with this card.
Above, a chart of relative power consumption. Again the Wattage shown is the card with the GPU(s) stressed 100%, showing only the peak GPU power draw, not the power consumption of the entire PC and not the average gaming power consumption.
Here is Guru3D's power supply recommendation:
Radeon HD 7970 - On your average system the card requires you to have a 550 Watt power supply unit.
Radeon HD 7970 Crossfire - On your average system the cards require you to have a 750 Watt power supply unit as minimum.
If you are going to overclock GPU or processor, then we do recommend you purchase something with some more stamina.
There are many good PSUs out there, please do have a look at our many PSU reviews as we have loads of recommended PSUs for you to check out in there. What would happen if your PSU can't cope with the load:
bad 3D performance
spontaneous reset or imminent shutdown of the PC
freezing during gameplay
PSU overload can cause it to break down
Let's move to the next page where we'll look into GPU heat levels and noise levels coming from this graphics card.
ASUS Radeon R9-290X Matrix review In this review we will benchmark and test the ASUS Radeon R9-290X Matrix Platinum edition. This Radeon R9-290X has been overhauled from A to Z. Yeah, the GPU might have remained in-tact, however the g...
ASUS Radeon R9-290 DirectCU II OC review We review the ASUS Radeon R9 290 DirectCU II OC edition. Ever since AMD released their Hawaii based GPUs they have been popular. The reference cards might run hot, but the custom cooled editions from...
ASUS Radeon R9-290X DirectCU II OC review We review the ASUS Radeon R9 290X DirectCU II OC edition. A lot of you guys have been waiting on a custom cooled version of this product. Armed with the latest revision of the DirectCU II.
ASUS Radeon R9-280X DirectCU II TOP review In this review we take a peek at the Radeon R9-280X from ASUS, they plastered the GPU on a custom PCB, tweaked it and then applied their DirectCUII cooling technology. As such the product should be interesting for many of you. Follow us into this review where we'll look at temperatures, noise, performance, Frame latency and we'll even give Ultra High Definition gaming a go with the hottest game titles on the globe.