HIS Radeon 6770 ICEQX Turbo Crossfire review
Posted by Hilbert Hagedoorn on: 07/20/2011 01:00 PM [ 0 comment(s) ]
Overclocking The R6770
As most of you know, with most videocards you can apply a simple series of tricks to boost the overall performance a little. You can do this at two levels, namely tweaking by enabling registry or BIOS hacks, or very simply to tamper with Image Quality. And then there is overclocking, which will give you the best possible results by far.
What do we need?
One of the best tools for overclocking NVIDIA and ATI videocards is our own AfterBurner which will work with 90% of the graphics cards out there. We can really recommend it, download here.
Where should we go?
Overclocking: By increasing the frequency of the videocard's memory and GPU, we can make the videocard increase its calculation clock cycles per second. It sounds hard, but it really can be done in less than a few minutes. I always tend to recommend to novice users and beginners, to not increase the frequency any higher than 5% on the core and memory clock. Example: If your card runs at 600 MHz (which is pretty common these days) then I suggest that you don't increase the frequency any higher than 30 to 50 MHz.
More advanced users push the frequency often way higher. Usually when your 3D graphics start to show artifacts such as white dots ("snow"), you should back down 10-15 MHz and leave it at that. Usually when you are overclocking too hard, it'll start to show artifacts, empty polygons or it will even freeze. Carefully find that limit and then back down at least 20 MHz from the moment you notice an artifact. Look carefully and observe well. I really wouldn't know why you'd need to overclock today's tested card anyway, but we'll still show it.
All in all... do it at your own risk.
|Core Clock: 850MHz||Core Clock: 880MHz||Core Clock: 960MHz|
|Shader Clock: 850MHz||Shader Clock: 880MHz||Shader Clock: 960MHz|
|Memory Clock: 4800MHz||Memory Clock: 5000MHz||Memory Clock: 5200MHz|
Now we left the fan RPM control at default. We reached a very decent overclock showing a bump in overall performance. The temps did not change very much but got closer to 60 Degrees C, DBA levels go tiny bit up. You can also try and go a little higher by increasing fan RPM of course, your call to make.
Voltage tweaking is not an option hence you can only overclock 'the good old fashioned way'.
Anyway, with Afterburner we took her upwards to 960 MHz and a 5200 MHz on the memory. Let's have a look at the reward, the performance increase.
Above we have Call of Duty: Modern Warfare 2, maxed out image quality settings as before with 4xAA 16xAF
Above we have Battlefield Bad Company 2, maxed out image quality settings as before with 8xAA 16xAF
Above, we can see 3DMark 11 - the Performance mode is applied here.
We test and review the a HIS Radeon HD 7950 HIS IceQ X, this 30 CM sized beast is one heck of a graphics card. Custom PCB, custom cooling, it's low noise and being a Boost edition card series, it clocks in at 950 MHz.
HIS Radeon HD 7850 4GB iPower IceQ Turbo review
We test and review the a HIS Radeon HD 7850 iPower IceQ Turbo as single card and in Crossfire today. The HIS Radeon HD 7850 iPower IceQ Turbo is a factory overclocked 4GB version of the Radeon HD 7850 graphics card.
HIS Radeon HD 7970 X Turbo edition review
We review the HIS Radeon HD 7970 X Turbo edition. With this card they took the new Tahiti XT2 and redesigned the R7970 board from ground up. though very long the end result is a 31cm PCB with mane power phases and optimizations. Fun to see are the voltage and FAN monitor LED options. Most impressive however is the sheer amount of monitor connectors HIS injected into this product, four DisplayPort connectors, one HDMI and a DVI connector. If needed you can go for Eyefinity6. Oh did I mention already that the factory set boost clock frequency is 1180 Mhz ?
HIS Radeon HD 7950 ICEQ Turbo review
We review the HIS Radeon HD 7950 IceQX Turbo. The product comes factory overclocked very nicely for you as it is running a gentle 900 MHz clock frequency. HIS uses a custom PCB and dual-slot cooler making the card very easy to install. Despite that factory overclock and that cooler the noise levels remain at very low levels whereas the GPU temperatures remain downright excellent as we'll show you in this review.