Its the standard anno 2008. Graphics cards are pretty easy to install. This card was no different. Slide the card into a free PCIe 8x / 16x slot and connect a monitor. Connect the 6-pin PCIe power cable. You can now power up the PC. Once Windows boots up, install the latest Catalyst drivers and make sure your operating system is fully patched up, especially DirectX. After driver installation, reboot the PC and you are ready to go.
It's time to do some actual testing with these cards. We'll start off by showing you some tests we have done on overall power consumption of the PC. Looking at it from a performance versus wattage point of view, the power consumption is really good with the new 55nm products. Our single card test system is a Core 2 Duo E8400 (3GHz) Processor, the nForce 680i SLI mainboard, a passive water-cooling solution on the CPU, 2GB memory, DVD-ROM and WD Raptor drive. Have a look:
System Under load
Radeon HD 4850 1GB
A single Radeon HD 4850/4870 series requires you to have a 450-500 Watt power supply unit at minimum if you use it in a high-end system, and I think that's barely on the safe side. Also recommended is 32 AMP's on the 12 volts rails for stable power distribution (in a single card configuration). Please make note of the fact that the card uses two 6-pin power connectors.
Crossfire is something else, you add another 130-150 Watts plus 8 AMPs on the 12V rails during gaming. I recommend a PSU of, at the very least, 750-800 Watts. Make sure you have some reserves folks. It's not that your PC will consume that much power, it's just that you want to make sure your PSU can deal with the hefty load and will stay stable during you entire gaming experience.
With three cards obviously 800+ Watt power supplies are recommended, and in fact even needed to be able to even supply something as simple as enough PCIe graphics power connectors.
There are many good PSU's available, over the years we reviewed a lot of them and have loads of recommended PSU's for you to check out in there, have a look. Things that can happen if your PSU can't cope with the load?:
bad 3D performance
spontaneous reset or imminent shutdown of the PC
freezes during gameplay
PSU overload can cause it to break down
The thermal envelope
Gigabyte Radeon HD 4850 1GB thermals We measured at a room temperature of 21-22 Degrees C, look at idle temperature and then load the GPU 100% for a couple of minutes and measure the temperature once a second and follow the temperature delta.
Typically the standard Radeon 4850 products come with a bit of an average cooler. Temperatures can rise up-to 95 Degrees C on these products. So I was quite thrilled to see a much better cooling solution mounted to this product.
Idle temps are roughly 35 Degrees C, yet when the GPU is fully utilized we measured 59 Degrees C, which is far better than the reference cooler.
None the less, always make sure you have a very well ventilated PC, as that heat is dumped inside your PC due to the dual slot cooling design. This is definitely one of the negatives of the product.
Noise Levels coming from the graphics card
When graphics cards produce a lot of heat, that heat usually needs to be transported away from the hot core as fast as possible. Often you'll see massive active fan solutions that can indeed get rid of the heat, yet all the fans these days make the PC a noisy son of a gun. I'm doing a little try-out today with noise monitoring, so basically the test we do is extremely subjective. We bought a certified dBA meter and will start measuring how many dBA originate from the PC. Why is this subjective, you ask? Well, there is always noise in the background, from the streets, from the HD, PSU fan etc etc, so this is by a mile or two not a precise measurement. You could only achieve objective measurement in a sound test chamber.
The human hearing system has different sensitivities at different frequencies. This means that the perception of noise is not at all equal at every frequency. Noise with significant measured levels (in dB) at high or low frequencies will not be as annoying as it would be when its energy is concentrated in the middle frequencies. In other words, the measured noise levels in dB will not reflect the actual human perception of the loudness of the noise. That's why we measure the dBa level. A specific circuit is added to the sound level meter to correct its reading in regard to this concept. This reading is the noise level in dBA. The letter A is added to indicate the correction that was made in the measurement. Frequencies below 1kHz and above 6kHz are attenuated, where as frequencies between 1kHz and 6kHz are amplified by the A weighting.
TYPICAL SOUND LEVELS
Jet takeoff (200 feet)
Shout (5 feet)
Heavy truck (50 feet)
Normal conversation (3 feet)
Bedroom at night
We start up a benchmark and leave it running for a while. The fan rotational speed remains constant. We take the dBA meter, move away 75 CM and then aim the device at the active fan on the graphics card.
With the Zalman cooler you can expect roughly 43-44 dBa at all times, since the ventilator RPM is fixed. Somewhat on the high side to be honest.
Gigabyte GeForce GTX 960 G1 Gaming 4GB review In this review we check out the 4GB version of the Gigabyte G1 Gaming GeForce GTX 960. The GTX 960 is the mainstream product that we figured has too little memory, will this 4GB version resolve our co...
Gigabyte G1.Sniper B6 review Let's review the budget enthusiast board G1.Sniper B6 from Gigabyte, it is based on the lower cost B85 chipset from Intel. B85 based motherboards typically end up in business desktops and normally ar...
Gigabyte GeForce GTX 960 WindForce 2X OC review In this review we check out the Gigabyte GeForce GTX 960 WindForce 2X. This product is slightly cheaper opposed to the G1 gaming version, it remains among the most silent of all the cards we tested. T...
Gigabyte GeForce GTX 960 G1 Gaming review In this review we check out the Gigabyte G1 Gaming GeForce GTX 960. This product is gorgeous as it is the most silent of all the cards we tested. Next to some fantastic looks the product comes factory...