MSI Radeon HD 7790 TurboDuo OC review
Metro Last Light VGA Graphics Benchmark performance test
Noctua NH-U12S and NH-U14S review
ASUS GeForce GTX 670 DirectCU Mini review
OCZ Vertex 3.20 SSD review
Cooler Master Eisberg 240L Prestige review
Guru3D and OCZ Contest - PC Power 1200W PSU Giveaway
MSI GeForce GTX 650 Ti BOOST OC review
ASUS ROG ORION PRO Gaming Headset Review
Guru3D Rig of the Month - April 2013
G.Skill Falcon II 128GB SSD review
Posted by Hilbert Hagedoorn on: 02/21/2010 02:00 PM [ 0 comment(s) ]
Product gallery
Related Articles
Product gallery
On the next few pages we'll show you some photos. The images were taken at high-resolution and then cropped and scaled down. The camera used was a Canon 450D 12 MegaPixel.
You can find the model we tested under the product code (SKU) FM-25S2I-128GBF2 and this is the 2.5" SATA II 128 GB version. You should easily be able to place it somewhere in your chassis.
And though the photo would make you think otherwise, of course, it's a perfect fit for laptops. This SSD would bring a whole lot of performance onto that laptop alright, all at low power consumption at 2 Watt and virtually no heat.
Slim and light-weight, 9.5mm tall, it's the standard for notebook drives. When we look at the connectors, we spot the standard power and SATA connector, this drive is SATA2 compatible.
To your right you can see two pins, this is a jumper which needs to be enabled if you like to flash new firmware into the SSD. Though the latest Firmware's don't even require you to do this.
Installation wise it's the same as a traditional HDD. Pop it in, connect it, bind it, format it and you are good to go at horribly fast speeds. It uses the same connectors as an SATA storage device.
G.Skill Sniper 8GB CL7 DDR3 memory review
G.Skill designed another 8GB low voltage DDR3 kit (2x 4GB) that can be set at 1600 MHz yet still run a CAS latency of 7. And that is truly interesting because the denser the ICs get, the higher latency typically gets.
G.Skill 2x4GB CL7 1600 MHz Trident DDR3 review
We feel that more memory is rather important, and in that trend memory manufacturers have started to increase the density of DIMM modules. Where 1 and 2GB DIMM modules have been the standard, we now see very good progress in 4 GB DIMM modules. Today we\'ll do things a little different, G.Skill designed a 8GB low voltage DDR3 kit (2x 4GB) that can be set at 1600 MHz yet still run a CAS latency of 7. And that is truly interesting because the denser the ICs get, the higher latency typically gets.
G.Skill Flare DDR3 2000 MHZ C7 AMD kit review
We test and review the G.Skill Flare DDR3 2000 MHZ C7 AMD kit. These kits are optimized for AMD platforms preferably with the new six-core X6 processors, and in specific some ASUS motherboards. The kit we'll be testing today obviously comes from that series and is a 2,000MHz CL7-9-7-24 1.65V 4GB (2GBx2) DDR3 kit with its latest Flare heatsinks.
G.Skill Phoenix PRO 120GB SSD review
The SSD tested today once again is the Phoenix series from G.Skill. After we tested their 100GB Phoenix SSD (which received a very positive review) G.Skill instantly requested if we would like to review the 120GB PRO model. Both drives pretty much are the same thing, same controller ... The 100GB Phoenix uses Samsung memory though but the trick is that there is 20GB extra volume space available on the new 120GB Pro (compared to the 100GB model) for nearly the same price. A new Firmware for the SandForce 1200 based controller that is inside this 120GB model simply reserves less NAND flash memory for its data-compression scheme. As a result the overall write performance could be a tiny bit slower, but only a few percent as best. It however will give you 20 GB more space to play around with at the same price. And since price per GB is everything in the land of SSDs -- this certainly is a significant for any vendor and for you as an end-user.
G.Skill designed another 8GB low voltage DDR3 kit (2x 4GB) that can be set at 1600 MHz yet still run a CAS latency of 7. And that is truly interesting because the denser the ICs get, the higher latency typically gets.
G.Skill 2x4GB CL7 1600 MHz Trident DDR3 review
We feel that more memory is rather important, and in that trend memory manufacturers have started to increase the density of DIMM modules. Where 1 and 2GB DIMM modules have been the standard, we now see very good progress in 4 GB DIMM modules. Today we\'ll do things a little different, G.Skill designed a 8GB low voltage DDR3 kit (2x 4GB) that can be set at 1600 MHz yet still run a CAS latency of 7. And that is truly interesting because the denser the ICs get, the higher latency typically gets.
G.Skill Flare DDR3 2000 MHZ C7 AMD kit review
We test and review the G.Skill Flare DDR3 2000 MHZ C7 AMD kit. These kits are optimized for AMD platforms preferably with the new six-core X6 processors, and in specific some ASUS motherboards. The kit we'll be testing today obviously comes from that series and is a 2,000MHz CL7-9-7-24 1.65V 4GB (2GBx2) DDR3 kit with its latest Flare heatsinks.
G.Skill Phoenix PRO 120GB SSD review
The SSD tested today once again is the Phoenix series from G.Skill. After we tested their 100GB Phoenix SSD (which received a very positive review) G.Skill instantly requested if we would like to review the 120GB PRO model. Both drives pretty much are the same thing, same controller ... The 100GB Phoenix uses Samsung memory though but the trick is that there is 20GB extra volume space available on the new 120GB Pro (compared to the 100GB model) for nearly the same price. A new Firmware for the SandForce 1200 based controller that is inside this 120GB model simply reserves less NAND flash memory for its data-compression scheme. As a result the overall write performance could be a tiny bit slower, but only a few percent as best. It however will give you 20 GB more space to play around with at the same price. And since price per GB is everything in the land of SSDs -- this certainly is a significant for any vendor and for you as an end-user.